HIPE Multi Zone Walk Through Metal Detector

General Description
The HI-PE Multi Zone is a high performance walk-through metal detector which exceeds all International Security Standards.

A “height on person” display actually indicates, by means of illuminated LED’s, the position of the weapon on the person. The location zones are not fixed, as in the case of walk-through metal detectors with multiple receiver-transmitter coils, but are variable and continuous so as to achieve optimum resolution.

The panels are washable and will not lose their shape even in humid conditions; they are also equipped with shock absorbent edges to protect it against damages.

HI-PE Multi Zone Walk Through Metal Detector can be supplied, on request, with two emergency batteries that automatically come into operation in the event of a mains failure.

A Photocell transit count, an option, allows for the counting of the number of people passing through the walk through metal detector.

Locating The Weapons Detected
In case of detection of metallic mass, the HI-PE Multi Zone walk-through metal detector not only provides an acoustical and optical alarm, it also gives an illuminated “height on person” indication by means of two bar displays, which are built into the antenna of the metal detector.

These may be programmed to provide a display either on both sides or on just one side of the gate.

The special signal analysis system allows the zones in which the metal masses are detected to be displayed with a high degree of precision.

This allows inspection procedures to be reduced and consequently provides a significant increase in the rate of people passing through.

Advantages
• Complete Security Detection
• Highly Visible Double Display
• Provides Single or Multiple Location of Weapons in Transit
• Very High Speed of Detection
• High Immunity to External Interferences
• Direct Selection of the International Security Standards
• High Reliability
• Local or Remote Programming with Networking Capabilities

 

Documentation HIPE Multi Zone Brochure

Technical Data

Main features
• Adjustable sensitivity with a wide range of settings.
• International Standards: immediate selection of International Security Standards.
• High detection speed: up to 45 feet per second.
• Very high immunity to both electrical and mechanical interference.
• Programmable operation controlled by microprocessor
• Programming: via built-in keypad and RDU or RS232/RS485 serial connection to PC or computer network.
• Programming access protected by a mechanical lock and two alphanumeric passwords.
• Cable-free automatic synchronization between two or more walk-though metal detectors at a minimum distance of 2 inches from each other.
• High-integration professional electronics and maximum reliability.
• Control unit incorporated into the detector.
• No need for initial or periodic calibration.
• Easy maintenance: the control unit can be replaced within one minute.
• Color: light grey RAL 7040

Alarms
Visual signaling:
• Multi-zone display bar for "height on person" localization.
• High intensity display.
• Green and red signals.
• Signal proportional to the mass of the object detected.

Audible signaling:
• High acoustic intensity alarm signal.
• Volume and tone of alarm signal can be programmed.
• Steady tone or tone length proportional to the mass of the object detected.

Certification and conformity
• Harmless to wearers of pacemakers or other vital support systems, pregnant women and magnetic storage media (floppy disks, audio cassettes, video cassettes and similar).
• Conforms to the FAA "3-Gun-Test" standard and to the NILECJ-0601-00 standards for all security levels.
• Satisfies EC regulations and international standards relating to electrical safety and electromagnetic compatibility (EMC).

Installation Data
Power Supply:
• 115 / 230 VAC, ±15%, 45-65 Hz, 30 VA MAX
Inputs:
• RS-232C interface for the connection with a terminal, a computer or an external modem
• RS-232C interface for the network connection with other CEIA walk through metal detectors
• Temperature and relative humidity: from -15°C to +50°C; from 0 to 95% (without condensation)

Photocell transit counter Photocell transit counter and automatic alarm rate calculation Built into both panel and column antennae, the photocells allow the number of people passing through the walk through metal detector to be counted. The photocells are particularly useful in all situations where statistical analysis has to be carried out on the access point (number of transits, alarms and percentage of alarms).
Back up batteries Back up batteries with 45 minutes of independent operation Two 12V-0.8Ah batteries built into the antenna which switch in automatically and allow about half an hour of independent operation (low power mode) in the event of a mains failure. The batteries recharge automatically when power returns.
Outdoor version Waterproof degree IP55
External Main Battery & Supply Unit MBSU including emergency battery External Main Battery Supply unit, including two 12 Vdc 7Ah emergency batteries and a charger. Battery life (normal condition): 9h max. Recharging time: 7h at 50% of the full charge. Protection degree (lEG 529) : IP55
Personal Effect Depository This article acts both as a spacer between the X-ray unit and the walk through metal detector and as a temporary depository for metal personal effects which are not of dubious nature and therefore not required to undergo X-ray analysis (coins, keys and so on). The base is constructed in material that guarantees maximum compatibility with the walk-though metal detector, and in such a way as not to transmit any mechanical shocks from the X-ray unit to the inspection gate.
MDSCOPE Software package specifically developed by CEIA in order to allow easy and complete testing of the functioning of a walk-through metal detector - without the use of special instrumentation - both during the setting up phase and on the occasion of periodic tests. Using a personal computer, MDSCOPE allows adjustment and monitoring of the metal detector, as well as the storage and printing of the data gathered.
Remote Control Unit with 20m of connection cable. The RCU unit, which is connected to the detector via a serial link, allows programming to be carried out by remote control. The unit also provides audible and visual alarm signalling, with a bar-graph indication that is proportional to the metallic mass in transit.
Ethernet Network Controller The MDNC-1 is an Ethernet Network Controller that can be connected to CEIA Walk Through Metal Detectors through the RS-232 interface. It contains a real-time clock with battery backup, and a large buffer for storage of more than twenty thousand transit events. This ensures that no data is lost in case of a network outage. As soon as the network service resumes the transit data is transferred to the NetID™ database. The MDNC-1 is supplied with the MDNC Admin MS Windows application, which is used to assign the desired network configuration and the encryption key.

Comparable Products
The H-PE Multi Zone offers similar operating capabilities as the following walk-through metal detectors: Garrett PD 6500i, Metor 200HS, Metor 200, Metor 200 wp and Metor 250.